Are you currently trying to locate advice around How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough job. If the old tub is readily obtainable, the job can relocate speedily; if you need to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will require a helper to move out the old tub as well as set in the new one. See to it you have certified on your own for the task and also fit attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to take into consideration using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This write-up will certainly assist you set up a new bath tub in your shower room if you have actually already bought a new tub and do not need to transform the setup of your previous water system pipelines.
Your devices and also product checklist should consist of the following:
Planning for the Setup
To start with, the supporting frame supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the restricted access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are useful in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water as well as examine all joints and new pipework for leaks and also tighten them if required. Load the bath tub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait until the bath tub has actually been used at least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Secure the faucet in place with the producer supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, causing the water to pass through the wall between the bath as well as the tiling, leading to issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on a different web blog. Enjoyed our piece? Please share it. Help another person locate it. Many thanks for taking the time to read it.
Just a call away!